From: Berk Demir (berk@linux.org.tr)
Date: Mon 09 Dec 2002 - 22:25:48 EET
On Mon, 9 Dec 2002, Evren YILDIZ wrote:
> At=FDl durumdaki bir makinaya, P200 64 MB ECC RAM, OpenBSD 3.2 kurmu=FEtu=
m
> zaman=FDnda. Boot ederken baz=FD mesajlar g=F6z=FCme =E7arpt=FD,
>
> "ahc1: PCI error Interrupt at seqaddr"
>
>
> pcibios0: pcibios_get_intr_routing - function not supported
Merhaba,
Kurdugunuz makine buyuk ihtimalle markali bir makine. Bunu yukaridaki
pcibios_get_intr_routing cagrisinin hata versinden ve Adapted AIC 7870
on-board SCSI controller kullandiginda dolayi tahmin ediyorum.
Tavsiyem, eger hala bulabilirseniz makineye bir BIOS guncellemesi
yapmaniz. 3. parti bir BIOS imaji kullanmaya calismayin. Ureticisinin
sitesinden baska bir yerden imaj cekmeyin.
Bu arada OpenBSD 3.2'yi hangi yol ile kurdunuz ? (ftp, cd-rom, vb.).
Eger CD ise hangi bu CD'yi satin mi aldiniz (resmi OpenBSD CD'si) yoksa
internet uzerinden bir yerden mi indirdiniz.
Bu problem 3.2'nin snapshot'larinda vardi. 3.2 duyurulmadan once bu
problem giderilmisti diye animsiyorum. CVS loglarina bakabilirsiniz.
Kolay gelsin,
-bdd
>
>
> pci0 at mainbus0 bus 0: configuration mode 2 (bios)
> pchb0 at pci0 dev 0 function 0 "Intel 82434LX/NX PCI/Cache/DRAM" rev
> 0x11
> ahc1 at pci0 dev 1 function 0 "Adaptec AIC-7870" rev 0x03ahc1: Using
> left over BIOS settings : irq 14
> ahc1: aic7870: Wide Channel A, SCSI Id=3D7, 16/255 SCBs
> scsibus0 at ahc1: 16 targets
> ahc1: target 1 synchronous at 10.0MHz, offset =3D 0xf
> ahc1: PCI error Interrupt at seqaddr =3D 0x7
> ahc1: target 1 using tagged queuing
> sd0 at scsibus0 targ 1 lun 0: <CONNER, CFP2105S 2.14GB, 2D4D> SCSI2
> 0/direct fixed
> sd0: 2048MB, 3940 cyl, 10 head, 106 sec, 512 bytes/sec, 4194304 sec
> total
> ahc1: target 2 synchronous at 10.0MHz, offset =3D 0xf
> ahc1: PCI error Interrupt at seqaddr =3D 0x9
> ahc1: target 2 using tagged queuing
> sd1 at scsibus0 targ 2 lun 0: <CONNER, CFP1060S 1.05GB, 2035> SCSI2
> 0/direct fixed
> sd1: 1013MB, 2756 cyl, 8 head, 94 sec, 512 bytes/sec, 2074880 sec total
> ahc1: PCI error Interrupt at seqaddr =3D 0x1a
> ahc1: PCI error Interrupt at seqaddr =3D 0x1a
> ahc1: PCI error Interrupt at seqaddr =3D 0x1c5
> ahc1: target 5 synchronous at 10.0MHz, offset =3D 0xf
> ahc1: PCI error Interrupt at seqaddr =3D 0x7
> ahc1: target 5 using tagged queuing
> sd2 at scsibus0 targ 5 lun 0: <SEAGATE, ST31230N, 0300> SCSI2 0/direct
> fixed
> sd2: 1010MB, 3992 cyl, 5 head, 103 sec, 512 bytes/sec, 2069860 sec total
> ahc1: PCI error Interrupt at seqaddr =3D 0x1a
> ahc1: PCI error Interrupt at seqaddr =3D 0x1a