From: Rüştü Derici (rustuderici@gmail.com)
Date: Tue 27 Dec 2005 - 00:42:25 EET
>00:0a.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x
DEC-Tulip compatible 10/100 Ethernet (rev 40)
dmesg da gordugunuz satir
linux un device i gordugunu anlatıyor ona bir surucu atamayı başardığını değil.
tahminimce kernelinizde davicom icin gereken modul derlenmiş durumda değil
kernelinizi tekrar derleme imkanınız varsa bunu denemenizi tavsiye ederim.
gereken modul ismi ya tulip olarak geçecektir yada direk davicom
yazacaktır şu an emin degilim
..yada en basiti 6$a bir realtek(default kernelde yuklu oluyor
genelde...) ya da 3Com(bu da kalitesine ragmen default kernelde yuklu
olmayabiliyor) 100Mbit lik bir ethernet kartı alıp davicomun yarattığı
tüm sıkıntılardan da kurtulabilirsiniz.. ki muhtemelen ben öyle
yapardım :)
Saygılar,
rustu
On 12/27/05, Ömer F. USTA <omerusta@gmail.com> wrote:
> ifconfig eth0 up
> /etc/init.d/network start
> (suse icin)(slack te eth0 veya benzeri bir ismi olabilir )
>
> 26.12.2005 tarihinde Oguz < oguzzz@gmail.com> yazmış:
> > # Config information for eth0:
> > IPADDR[0]=""
> > NETMASK[0]=""
> > USE_DHCP[0]="yes"
> > DHCP_HOSTNAME[0]=" 10.0.0.2"
> >
> > bu ayarlari yaptim, ifconfig'de eth0 i goremedim
> > aynen soyle:
> > bash-3.00# ping 10.0.0.2
> >
> > connect: Network is unreachable
> >
> > bash-3.00# ifconfig
> >
> > lo Link encap:Local Loopback
> > inet addr:
> > 127.0.0.1 Mask:
> > 255.0.0.0
> > UP LOOPBACK RUNNING MTU:16436 Metric:1
> >
> > RX packets:2 errors:0 dropped:0 overruns:0 frame:0
> > TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
> > collisions:0 txqueuelen:0
> >
> >
> > RX bytes:100 (100.0 b) TX bytes:100 (100.0 b)
> > -----------------------------
> >
> > dmesg'de eth0 a dair birsey goremedim ama lspci da
> > 00:0a.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x DEC-Tulip
> compatible 10/100 Ethernet (rev 40)
> >
> >
> >
> >
> > var
> >
> > ip adresleri degismis olabilir isyerimde de tamamen ayni problemi
> yasiyorum, ornekleri isyerimden verdim denemeyi evde yaptim..
> >
> > saygilar...
> >
> >
> > 2005/12/25, Rüştü Derici <rustuderici@gmail.com>:
> >
> > > daha onceki sorunuzu goremedim ama
> > > su an gorduklerime dayanarak bir sonuc cikartmaya calistim.
> > >
> > > oncelikle kablonuzun saglikli bir sekilde baglanabildiginden emin olun..
> > > ayrica dmesg icerisinde eth0 device ina ethernet kartiniz ataniyormu
> > > kontrol edin..
> > >
> > > eger bunlar tamam sa
> > >
> > > /etc/rc.d/rc.inet1.conf
> > > ayarlarinin
> > > # Config information for eth0:
> > > IPADDR[0]=""
> > > NETMASK[0]=""
> > > USE_DHCP[0]="yes"
> > > DHCP_HOSTNAME[0]=" 192.168.1.1"
> > >
> > > seklinde oldugundan emin olun
> > > ..
> > > umarim yardimci olabilmisimdir..
> > > saygilar
> > > rustu
> > >
> > > On 12/24/05, Oguz <oguzzz@gmail.com > wrote:
> > > > daha oncede belirtmistim bu problemimi fakat size sundugum kaynak
> > > > yetersizliginden problemi cozememistik. aklima ne geliyorsa sunuyorum.
> > > > sorunumu hatirlatayim: modeme (ve agdaki makinelere) erisemiyorum.
> > > >
> > > >
> ###################################################################################
> > > >
> > > > bash-3.00# lspci
> > > > 00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX
> Host
> > > > bridge (rev 03)
> > > > 00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP
> bridge
> > > > (rev 03)
> > > > 00:04.0 ISA bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
> > > >
> > > > 00:04.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev
> 01)
> > > > 00:04.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev
> 01)
> > > > 00:04.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 02)
> > > >
> > > > 00:0a.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x
> DEC-Tulip
> > > > compatible 10/100 Ethernet (rev 40)
> > > > 01:00.0 VGA compatible controller: S3 Inc. Savage 4 (rev 02)
> > > > bash-3.00#
> > > >
> ###################################################################################
> > > >
> > > >
> > > >
> > > > netconfig -> statik
> > > > --
> > > > netconfig statik
> > > >
> > > > bash-3.00# ifconfig
> > > > eth0 Link encap:Ethernet HWaddr 00:08:A1:8C:34:1A
> > > >
> > > > inet addr: 192.168.1.29 Bcast:192.168.1.255 Mask: 255.255.255.0
> > > > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> > > >
> > > > RX packets:197 errors:0 dropped:0 overruns:0 frame:0
> > > > TX packets:36 errors:0 dropped:0 overruns:0 carrier:0
> > > > collisions:0 txqueuelen:1000
> > > > RX bytes:20740 (20.2 Kb) TX bytes:1536 (
> > > > 1.5 Kb)
> > > > Interrupt:10 Base address:0xd000
> > > >
> > > > lo Link encap:Local Loopback
> > > > inet addr:127.0.0.1 Mask: 255.0.0.0
> > > > UP LOOPBACK RUNNING MTU:16436 Metric:1
> > > >
> > > > RX packets:25 errors:0 dropped:0 overruns:0 frame:0
> > > > TX packets:25 errors:0 dropped:0 overruns:0 carrier:0
> > > > collisions:0 txqueuelen:0
> > > > RX bytes:2648 (2.5 Kb) TX bytes:2648 (
> > > > 2.5 Kb)
> > > >
> > > > bash-3.00#
> > > >
> > > > -------------------------------------
> > > > bash-3.00# route
> > > > Kernel IP routing table
> > > > Destination Gateway Genmask Flags Metric Ref Use Iface
> > > > localnet *
> > > > 255.255.255.0 U 0 0 0 eth0
> > > > loopback * 255.0.0.0 U 0 0 0 lo
> > > > bash-3.00#
> > > >
> > > > ---------------------------------------
> > > >
> > > > bash-3.00# routel
> > > > target gateway source proto scope dev tbl
> > > > 192.168.1.0/ 24 192.168.1.29
> > > > kernel link eth0
> > > > 127.0.0.0/ 8 link lo
> > > > 192.168.1.0 broadcast
> > > > 192.168.1.29 kernel link eth0 local
> > > > 127.255.255.255 broadcast 127.0.0.1 kernel link lo local
> > > >
> > > > 192.168.1.255 broadcast 192.168.1.29 kernel link eth0 local
> > > > 192.168.1.29 local
> > > > 192.168.1.29 kernel host eth0 local
> > > > 127.0.0.0 broadcast 127.0.0.1 kernel link lo local
> > > >
> > > > 127.0.0.1 local 127.0.0.1 kernel host lo local
> > > > 127.0.0.0/ 8 local 127.0.0.1
> > > > kernel host lo local
> > > > bash-3.00#
> > > > -------------------------------------------------
> > > > bash-3.00# ping 192.168.1.1
> > > > PING 192.168.1.1 (
> > > > 192.168.1.1) 56(84) bytes of data.
> > > > From 192.168.1.29 icmp_seq=1 Destination Host Unreachable
> > > > From 192.168.1.29 icmp_seq=2 Destination Host Unreachable
> > > >
> > > > From 192.168.1.29 icmp_seq=3 Destination Host Unreachable
> > > > From 192.168.1.29 icmp_seq=4 Destination Host Unreachable
> > > > From
> > > > 192.168.1.29 icmp_seq=5 Destination Host Unreachable
> > > > ....
> > > > ....
> > > >
> > > > --- 192.168.1.1 ping statistics ---
> > > > 24 packets transmitted, 0 received, +21 errors, 100% packet loss, time
> > > > 23028ms
> > > >
> > > > , pipe 3
> > > > bash-3.00#
> > > >
> -------------------------------------------------------------
> > > >
> > > > netconfig -> DHCP
> > > > --
> > > > ---------------------------------------------
> > > >
> > > >
> > > >
> > > > bash-3.00# ifconfig
> > > > lo Link encap:Local Loopback
> > > > inet addr:127.0.0.1 Mask: 255.0.0.0
> > > > UP LOOPBACK RUNNING MTU:16436 Metric:1
> > > >
> > > > RX packets:2 errors:0 dropped:0 overruns:0 frame:0
> > > > TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
> > > > collisions:0 txqueuelen:0
> > > > RX bytes:100 (100.0 b) TX bytes:100 (
> > > > 100.0 b)
> > > >
> > > >
> ---------------------------------------------------------
> > > > bash-3.00# ifconfig eth0 up
> > > > bash-3.00# ifconfig
> > > > eth0 Link encap:Ethernet HWaddr 00:08:A1:8C:34:1A
> > > > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> > > >
> > > > RX packets:76 errors:0 dropped:0 overruns:0 frame:0
> > > > TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
> > > > collisions:0 txqueuelen:1000
> > > > RX bytes:7502 (7.3 Kb) TX bytes:2360 (
> > > > 2.3 Kb)
> > > > Interrupt:10 Base address:0xd000
> > > >
> > > > lo Link encap:Local Loopback
> > > > inet addr:127.0.0.1 Mask:255.0.0.0
> > > > UP LOOPBACK RUNNING MTU:16436 Metric:1
> > > >
> > > > RX packets:2 errors:0 dropped:0 overruns:0 frame:0
> > > > TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
> > > > collisions:0 txqueuelen:0
> > > > RX bytes:100 (100.0 b) TX bytes:100 (
> > > > 100.0 b)
> > > >
> > > > bash-3.00#
> > > >
> > > >
> -----------------------------------------------------------
> > > > bash-3.00# route
> > > > Kernel IP routing table
> > > > Destination Gateway Genmask Flags Metric Ref Use Iface
> > > >
> > > > loopback * 255.0.0.0 U 0 0 0 lo
> > > > --------------
> > > > bash-3.00# routel
> > > > target gateway source proto scope dev tbl
> > > >
> > > > 127.0.0.0/ 8 link lo
> > > > 127.255.255.255 broadcast 127.0.0.1
> > > > kernel link lo local
> > > > 127.0.0.0 broadcast 127.0.0.1 kernel link lo local
> > > > 127.0.0.1
> > > > local 127.0.0.1 kernel host lo local
> > > > 127.0.0.0/ 8 local 127.0.0.1 kernel host lo local
> > > >
> > > > ------------------------
> > > >
> > > > bash-3.00# ping 192.168.1.1
> > > > connect: Network is unreachable
> > > > bash-3.00#
> > > >
> > > > --------------------------
> > > >
> > > > Saygilar...
> > > >
> > > > Oguz ~
> > > > [ NCT {The Climbing Crew} ]
> > > > _______________________________________________
> > > > Linux-ag mailing list
> > > > Linux-ag@liste.linux.org.tr
> > > > http://liste.linux.org.tr/mailman/listinfo/linux-ag
> > > >
> > > >
> > > >
> > >
> > >
> > > _______________________________________________
> > > Linux-ag mailing list
> > > Linux-ag@liste.linux.org.tr
> > > http://liste.linux.org.tr/mailman/listinfo/linux-ag
> > >
> > >
> > >
> >
> >
> >
> > --
> >
> > Oguz ~ [NCT {The Climbing Crew}]
> > _______________________________________________
> > Linux-ag mailing list
> > Linux-ag@liste.linux.org.tr
> > http://liste.linux.org.tr/mailman/listinfo/linux-ag
> >
> >
> >
>
>
>
> --
> Ömer Fadıl USTA
> http://www.bilisimlab.com/
> _______________________________________________
> Linux-ag mailing list
> Linux-ag@liste.linux.org.tr
> http://liste.linux.org.tr/mailman/listinfo/linux-ag
>
>
>
_______________________________________________
Linux-ag mailing list
Linux-ag@liste.linux.org.tr
http://liste.linux.org.tr/mailman/listinfo/linux-ag