From: isa necat (isanecat@hotmail.com)
Date: Sat 15 May 2004 - 19:52:46 EEST
Arkadaslar,
Vaktinizi almak istemiyorum ama bir sorum olacak;
Mandrake 10 kurdum.(Kernel 2.6.3-4mdk) 'Surecom EP-320X-S' ethernet kartim
var. Kurulumda 'Myson MTD-8xx 10/100 PCI'olarak tanittigim bu karti acilista
hatali olarak gosteriyor ve ping yapmiyor. Su an makinama Knoppix ile ulasip
size bu mesaji atiyorum. Makinamdaki MS windowsu buyuk bir zevkle silmistim
ama pisman olmak istemiyorum. Kendi isimi kendim halletmek icim cok sorf
yaptim ama tatmin edici birsey bulamadim. Ethernet kartinin disketindeki
helpten birsey anlamadim. Linux'a yeni oldugum icin olabilir. Asagidaki
metin surucunun yardim dosyasidir.
Acil yardimlarinizi rica ediyorum.
Saygilarimla
Necat
>******* This document contains instructions on Linux driver installation
>for *******
>******* SURECOM EP-320X-S/S-1 100/10M Ethernet PCI Adapter
> *******
>
> The Linux driver for Myson MDT8xx compatible MAC chipset on
>this adapter has been embedded into Linux systems since kernel
>version 2.4.5, and this makes this adapter automatically detected
>and installed with the driver supported by Linux system.
>
> Therefore,
>
> 1. If your Linux kernel is still old version 2.2.x, please use
>and refer the driver supported for kernel version 2.2.x in
>\Linux\2.2.x directory on the driver diskette.
>
>
> 2. If your Linux kernel is version 2.4.x previous than version
>2.4.5, please get the latest kernel file from the web site of The
>Linux Kernel Archives (http://www.kernel.org/). Then, install and
>re-compile the downloaded latest kernel file into your current
>Linux system.
>
>
> 3. If your Linux kernel is or has been patched to version
>above 2.4.5 but you have not enabled or configured the MTD8xx
>compatible driver as dynamic loadable or embedded system module,
>then you could follow the step 4 to enable the driver and
>re-compile the kernel.
>
> If you could use the console command "#locate fealnx.o" to
>locate the module driver file or find the driver module file
>fealnx.o in kernel source /usr/src/linux-2.4.x/drivers/net in
>your Linux system, then you could load module into system by
>console command "insmod fealnx.o" and then "ifconfig eth0 up" to
>bring this adapter to work.
>
> You could use console command "linuxconf" to configure
>this adapter card too.
>
>
> 4. If your Linux kernel is any new version above than 2.4.5
>(included) and it is a new installation, you can configure the
>kernel by following console commands to enable the driver for
>SURECOM EP-320X-S/S-1 100/10M Ethernet PCI Adapter.
>
> #/usr/src/menuconfig
>
> Enable the option of "Myson MTD-8XX PCI Ethernet support"
>in "Ethernet (10 or 100 M bit)" of "Network device support" as a
>loadable module or system default module.
>
> #make dep
>
> #make clean
>
> #make bzImage
>
> #cp /usr/src/linux-2.4.X/arch/i386/boot/bzImage /boot
>
> Then, edit /etc/lilo.conf, run "/sbin/lilo", and then reboot
>your Linux system. After new kernel has been rebooted, it will
>automatically load the driver for this adapter.
_________________________________________________________________
STOP MORE SPAM with the new MSN 8 and get 2 months FREE*
http://join.msn.com/?page=features/junkmail
---
linux-baslangic listesinden cikmak ve tum listeci islemleri icin
http://liste.linux.org.tr/ adresini kullanabilirisniz.
Bu listeden cikmak icin
<a href="mailto:linux-baslangic-request@liste.linux.org.tr?Subject=unsubscribe"> tiklayiniz</a>