From: Selcuk Bozdag (bozdagselcuk@yahoo.com)
Date: Mon 05 Aug 2002 - 19:10:52 EEST
Selamlar,
Bir ara böyle birşeyle uğraştığım için yardım
edebileceğimi düşündüm.
Acaba "ifconfig" komutunu denediniz mi? README
kütüğünde de yazdığı gibi linux ethernet kartlarını
zaten çekirdeğinde desteklemektedir.(çok şanslıyız:)
Şimdi ifconfig yazıp enter'a bastığınızda karşınıza
şöyle iki paragraf gelebilir:
eth0 Link encap:Ethernet HWaddr 00:50:FC:2A:AB:7A
inet addr:192.168.1.1 Bcast:192.168.1.255
Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500
Metric:1
RX packets:0 errors:0 dropped:0 overruns:0
frame:0
TX packets:4 errors:0 dropped:0 overruns:0
carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:240 (240.0 b)
Interrupt:10 Base address:0x4000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:992 errors:0 dropped:0
overruns:0 frame:0
TX packets:992 errors:0 dropped:0
overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:76568 (74.7 Kb) TX bytes:76568
(74.7 Kb)
Bunlardan ilki yani "eth0" ile başlayan sizin
kartınızdır. Zaten böyle bir yazıyla karşılaşırsanız
emin olun ki Linux'unuz ethernet kartınızla çoktan
tanışmıştır. Sanırım sorunuza yanıt olabilir bu.
Daha ilerisi için eğer bu karta(yani eth0'a) bir IP
adresi atamak istiyorsanız:(örneğin 195.155.3.3)
ifconfig eth0 195.155.3.3
demeniz yeterli. ifconfig komutuyla ilgili daha geniş
bilgi için "man ifconfig" yazabilirsiniz.
iyi çalışmalar.
--- BORA ERESICI <boraeresici@ttnet.net.tr> wrote:
> Merhaba;
> Surecom ethernet kartini ne yaptiysam tanitamadim
> elimde sürücü leri de
> mevcut. ve bende RH 7.3 kullanıyorum yardim
> ederseniz acil olarak sevinirim.
> Readme den de bir sey anlamadgimi soylesem ... :)
>
>
> -- Attached file included as plaintext by Ecartis --
> -- File: Readme.txt
>
> ******* This document contains instructions on
> Linux driver installation for *******
> ******* SURECOM EP-320X-S/S-1 100/10M
> Ethernet PCI Adapter *******
>
> The Linux driver for Myson MDT8xx compatible MAC
> chipset on
> this adapter has been embedded into Linux systems
> since kernel
> version 2.4.5, and this makes this adapter
> automatically detected
> and installed with the driver supported by Linux
> system.
>
> Therefore,
>
> 1. If your Linux kernel is still old version
> 2.2.x, please use
> and refer the driver supported for kernel version
> 2.2.x in
> \Linux\2.2.x directory on the driver diskette.
>
>
> 2. If your Linux kernel is version 2.4.x
> previous than version
> 2.4.5, please get the latest kernel file from the
> web site of The
> Linux Kernel Archives (http://www.kernel.org/).
> Then, install and
> re-compile the downloaded latest kernel file into
> your current
> Linux system.
>
>
> 3. If your Linux kernel is or has been patched
> to version
> above 2.4.5 but you have not enabled or configured
> the MTD8xx
> compatible driver as dynamic loadable or embedded
> system module,
> then you could follow the step 4 to enable the
> driver and
> re-compile the kernel.
>
> If you could use the console command "#locate
> fealnx.o" to
> locate the module driver file or find the driver
> module file
> fealnx.o in kernel source
> /usr/src/linux-2.4.x/drivers/net in
> your Linux system, then you could load module into
> system by
> console command "insmod fealnx.o" and then
> "ifconfig eth0 up" to
> bring this adapter to work.
>
> You could use console command "linuxconf" to
> configure
> this adapter card too.
>
>
> 4. If your Linux kernel is any new version above
> than 2.4.5
> (included) and it is a new installation, you can
> configure the
> kernel by following console commands to enable the
> driver for
> SURECOM EP-320X-S/S-1 100/10M Ethernet PCI Adapter.
>
> #/usr/src/menuconfig
>
> Enable the option of "Myson MTD-8XX PCI
> Ethernet support"
> in "Ethernet (10 or 100 M bit)" of "Network device
> support" as a
> loadable module or system default module.
>
> #make dep
>
> #make clean
>
> #make bzImage
>
> #cp
> /usr/src/linux-2.4.X/arch/i386/boot/bzImage /boot
>
> Then, edit /etc/lilo.conf, run "/sbin/lilo",
> and then reboot
> your Linux system. After new kernel has been
> rebooted, it will
> automatically load the driver for this adapter.
>
__________________________________________________
Do You Yahoo!?
Yahoo! Health - Feel better, live better
http://health.yahoo.com